1408-EM3A-ENT 能源和功率监控模块

1408-EM3A-ENT 能源和功率监控模块

1408-EM3A-ENT 模块是 Allen-Bradley PowerMonitor 1000 系列的需求、能源和功率监控模块。作为PowerMonitor 1000系列的一部分，Allen-Bradley提供的其他类型的设备包括基本消耗表和基本消耗和故障排除仪表。1408-EM3A-ENT 模块上提供了一个集成以太网端口，用于网络通信。1408-EM3A-ENT 模块可在直流和交流输入电压下工作。

1408-EM3A-ENT模块旨在用作电路保护器件，不应用作电路保护继电器或电机过载继电器。为防止人身伤害和设备损坏，在开始与 1408-EM3A-ENT 模块的安装或维护相关的任何工作之前，必须断开所有电源。否则可能会导致财产损失、伤害甚至死亡。只有经过培训的技术人员才能进行与 1408-EM3A-ENT 模块的安装和维修相关的活动。

1408-EM3A-ENT 模块连接到三相或分相交流电源系统。它将电压和电流值转换为数字值，然后使用数字值计算功率、能量、电压和电流。RS-485接口支持的协议包括Modbus RTU从机、DH-485、DF1半双工从机和DF1全双工协议。设备的控制输入可以是 120 至 240 伏交流电或 125 至 250 伏直流电。1408-EM3A-ENT驱动器的工作温度范围为-10至60摄氏度。介电耐受额定值符合UL61010和EN61010。对于端接在 22-EM14A-ENT 驱动器上的电压和电流检测输入端接的电线，建议仅使用 1408 至 3 AWG 铜线。

1408-EM3A-ENT 能源和功率监控模块

The 1408-EM3A-ENT module is a demand, energy and power monitoring module for the Allen-Bradley PowerMonitor 1000 series. Other types of equipment offered by Allen-Bradley as part of the PowerMonitor 1000 series include basic consumption meters and basic consumption and troubleshooting meters. An integrated Ethernet port is provided on the 1408-EM3A-ENT module for network communication. The 1408-EM3A-ENT module operates at both DC and AC input voltages.

The 1408-EM3A-ENT module is intended to be used as a circuit protection device and should not be used as a circuit protection relay or motor overload relay. To prevent personal injury and equipment damage, all power supplies must be disconnected before starting any work related to the installation or maintenance of the 1408-EM3A-ENT module. Failure to do so may result in property damage, injury or even death. Only trained technicians are allowed to carry out activities related to the installation and servicing of the 1408-EM3A-ENT module.

The 1408-EM3A-ENT module is connected to a three-phase or split-phase AC power system. It converts voltage and current values to digital values, and then uses the digital values to calculate power, energy, voltage, and current. The protocols supported by the RS-485 interface include Modbus RTU slave, DH-485, DF1 half-duplex slave, and DF1 full-duplex. The control input of the device can be 120 to 240 volts AC or 125 to 250 volts DC. The 1408-EM3A-ENT drives operate in a temperature range of -10 to 60 degrees Celsius. Dielectric tolerance ratings are in line with UL61010 and EN61010. It is recommended to use only 1408 to 3 AWG copper wire for voltage and current detection input wires terminated on 22-EM14A-ENT drivers.

1408-EM3A-ENT 能源和功率监控模块

型号推荐
DO6603 康吉森    Triconex DCS    数字输入模块
PM6301A 康吉森    Triconex DCS    数字输入模块
DI6503 康吉森    Triconex DCS    数字输入模块
MP6004 康吉森    Triconex DCS    主处理器模块
Triconex 3721 康吉森    Triconex DCS    模拟输入模块
3511 康吉森    Triconex DCS    脉冲输入模块
3625 康吉森    Triconex DCS    24 vdc数字输出模块
3451 康吉森    Triconex DCS    通信模块
9765-210 康吉森    Triconex DCS    控制板终止
4000103-510 康吉森    Triconex DCS    通信模块
3008 康吉森    Triconex DCS    处理器模块
3700 康吉森    Triconex DCS    模拟输入三模冗余32 PT模块