GE DS3800HSQD1J1F 用于插入螺钉以将板固定在驱动器中

GE DS3800HSQD1J1F 用于插入螺钉以将板固定在驱动器中

GE 低 HP 序列板DS3800HSQD1J1F设计为每个角上都有一个孔，用于插入螺钉以将板固定在驱动器中。GE 低 HP 序列板DS1HSQD3800J1F还配备了 1 个 2 针连接器和 40 个 1 针连接器，带有固定杆，用于固定带状电缆。该板还装有 20 针连接器和 50 个 1 针连接器。该板还装有 20 个可擦除可编程只读存储器 （EPROM） 模块和 1 个琥珀色指示灯 LED 和 1 个红色指示灯 LED。

您计划更换的 GE 低 HP 序列板DS3800HSQD1J1F上可能安装了子卡。子卡是与主板一起使用的可选设备。它为电路板提供了额外的功能。子卡将信号传输到电路板。它还接收来自电路板的信号。它还从电路板获得为子卡供电的电流。子卡可以卸下并安装在更换板上。

卸下并安装子卡时佩戴腕带。要卸下子卡，请先拔下50针带状电缆。用一只手握住连接器并将其从板上的连接器中拉出。然后从支架上一次提起子卡的 1 个角。用两只手握住卡片并将其放入静态保护袋中。将卡存放在干净干燥的地方，直到准备好将其安装到更换板上。

GE DS3800HSQD1J1F 用于插入螺钉以将板固定在驱动器中

The GE Low HP sequence board DS3800HSQD1J1F is designed with a hole in each corner for inserting screws to secure the board in the drive. The GE Low HP sequence board DS1HSQD3800J1F is also equipped with 1 2-pin connector and 40 1-pin connectors with retainer rods for securing ribbon cables. The board is also equipped with 20-pin connectors and 50 1-pin connectors. The board is also equipped with 20 erasable programmable read-only memory (EPROM) modules and one amber LED and one red LED.

The GE low HP serial board DS3800HSQD1J1F that you plan to replace may have a subcard installed. The subcard is an optional device for use with the motherboard. It provides additional functionality to the board. The daughter card transmits the signal to the board. It also receives signals from the circuit board. It also gets the current from the circuit board that powers the daughter card. The subcard can be removed and installed on the replacement plate.

Wear a wrist strap when removing and installing a sub-card. To remove the sub-card, first unplug the 50-pin ribbon cable. Hold the connector with one hand and pull it out of the connector on the board. Then lift one corner of the subcard from the bracket at a time. Hold the card with two hands and place it in the static protection bag. Store the card in a clean, dry place until you are ready to install it onto the replacement board.

GE DS3800HSQD1J1F 用于插入螺钉以将板固定在驱动器中

型号推荐
IS200HFPRG1A    GE Fanuc    通用电气燃机卡件
IS200HFPAG2A    GE Fanuc    电磁阀模块
IS200HFPAG1A    GE Fanuc    输入输出模块
IS200GGXIG1A    GE Fanuc    输入输出模块
IS200FOSBH1A    GE Fanuc    控制卡件
IS200FOSAG1A    GE Fanuc    卡件模块
IS200EXIBG1A    GE Fanuc    卡件模块
IS200EXCSG1A    GE Fanuc    卡件模块
IS200ESELH1A    GE Fanuc    电磁阀模块
IS200ERSCG2A    GE Fanuc    电磁阀模块
IS200ERRRH1A    GE Fanuc    电磁阀模块