GE DS3800HSQD1J1C 序列总成卡的工业控制设备

GE DS3800HSQD1J1C 序列总成卡的工业控制设备

GE 低 HP 序列板DS3800HSQD1J1C设计为每个角上都有一个孔，用于插入螺钉以将板固定在驱动器中。GE 低 HP 序列板DS1HSQD3800J1C还配备了 1 个 2 针连接器和 40 个带固定杆的 1 针连接器，用于固定带状电缆。该板还装有 20 针连接器和 50 个 1 针连接器。该板还装有 20 个可擦除可编程只读存储器 （EPROM） 模块和 1 个琥珀色指示灯 LED 和 1 个红色指示灯 LED。

GE 低 HP 序列板DS3800HSQD1J1C通过 4 个螺钉固定在板架中。每个角安装1个螺钉。要卸下电路板，请先断开连接到电路板的带状电缆。某些连接器具有固定带状电缆的固定夹。在卸下带状电缆之前，请将夹子旋过连接器。然后，您可以通过握住带状电缆末端的连接器，用一只手将带状电缆拉开。

将所有带状电缆移开，然后小心地使用螺丝刀松开螺钉。确保螺丝刀不会划伤电路板表面或损坏任何组件。确保将所有螺钉放在一起，并将它们存放起来，以便在安装更换板时使用。如果缺少 1 颗螺钉，请将其放在驱动器内部。如果未找到，可能会导致短路，从而导致火灾或驱动器组件损坏。它可能导致火灾或电击受伤。

GE DS3800HSQD1J1C 序列总成卡的工业控制设备

The GE Low HP sequence board DS3800HSQD1J1C is designed with a hole in each corner for inserting screws to secure the board in the drive. The GE Low HP serial board DS1HSQD3800J1C is also equipped with 1 2-pin connector and 40 1-pin connectors with fixed rods for securing ribbon cables. The board is also equipped with 20-pin connectors and 50 1-pin connectors. The board is also equipped with 20 erasable programmable read-only memory (EPROM) modules and one amber LED and one red LED.

The GE low HP serial plate DS3800HSQD1J1C is secured in the plate frame by four screws. Install one screw at each corner. To remove the circuit board, disconnect the ribbon cable connected to the circuit board. Some connectors have clamping clips to secure the ribbon cable. Screw the clip over the connector before removing the ribbon cable. You can then pull the ribbon cable apart with one hand by holding the connector at the end of the ribbon cable.

Remove all ribbon cables, then carefully use a screwdriver to loosen the screws. Make sure the screwdriver does not scratch the board surface or damage any components. Make sure to put all the screws together and store them for use when installing the replacement plate. If 1 screw is missing, place it inside the drive. If not found, it could cause a short circuit, which could lead to a fire or damage to the drive assembly. It can cause fire or electric shock injuries.

GE DS3800HSQD1J1C 序列总成卡的工业控制设备

型号推荐
IS200HFPRG1A    GE Fanuc    通用电气燃机卡件
IS200HFPAG2A    GE Fanuc    电磁阀模块
IS200HFPAG1A    GE Fanuc    输入输出模块
IS200GGXIG1A    GE Fanuc    输入输出模块
IS200FOSBH1A    GE Fanuc    控制卡件
IS200FOSAG1A    GE Fanuc    卡件模块
IS200EXIBG1A    GE Fanuc    卡件模块
IS200EXCSG1A    GE Fanuc    卡件模块
IS200ESELH1A    GE Fanuc    电磁阀模块
IS200ERSCG2A    GE Fanuc    电磁阀模块
IS200ERRRH1A    GE Fanuc    电磁阀模块