欢迎光临厦门雄霸电子商务有限公司官网!
工控|工业|自动化进口DCS系统 机器人系统 大型伺服系统
全国咨询热线(Sunny)18059884797
联系我们
厦门雄霸电子商务有限公司
手机:18059884797
QQ:3095989363
邮箱:xiongbagk@gmail.com
地址 :福建省厦门市思明区吕岭路1733号2008单元(万科创想中心)
联系人:Sunny
您的位置: 首页>>产品展示 >
产品展示 》 GE 》 GE DS3800HSQD1G1C 序列板 能够监控驱动器的操作

GE DS3800HSQD1G1C 序列板 能够监控驱动器的操作

型号:DS3800HSQD1G1C

GE DS3800HSQD1G1C 序列板 能够监控驱动器的操作

品牌 GE 加工定制 否 输入范围 电压:-10伏至+10伏电流:4至20毫安 准确性 校准 电压范围 峰值信号输入必须在+13和- 13伏之间 灵敏度 70 dB CMRR

GE DS3800HSQD1G1C 序列板 能够监控驱动器的操作

GE 低 HP 序列板DS3800HSQD1G1C设计为每个角上都有一个孔,用于插入螺钉以将板固定在驱动器中。GE 低 HP 序列板DS1HSQD3800G1C还配备了 1 个 2 针连接器和 40 个带固定杆的 1 针连接器,用于固定带状电缆。该板还装有 20 针连接器和 50 个 1 针连接器。该板还装有 20 个可擦除可编程只读存储器 (EPROM) 模块和 1 个琥珀色指示灯 LED 和 1 个红色指示灯 LED。

GE 低 HP 序列板上的指示灯 LED DS3800HSQD1G1C使操作员或技术人员能够监控驱动器的操作。同时,操作员或技术人员可以监控其他驱动器和设备。这是因为通过看一眼指示灯 LED,技术人员或操作员可以观察是否发生了错误或操作是否正常进行。

当琥珀色指示灯亮起时,表示驱动器已启动,并且初始启动诊断测试已通过。如果驱动器已启动且琥珀色指示灯保持熄灭,则可能表示存在问题。这可能表示驱动器没有电源。检查是否所有电源都进入驱动器,以及电源是否按要求工作。如果电源可用,则驱动器可能无法通过启动时执行的初始诊断测试。能够启动驱动器后,请执行全方位的诊断测试以调查问题。

GE DS3800HSQD1G1C 序列板 能够监控驱动器的操作

GE DS3800HSQD1G1C 序列板 能够监控驱动器的操作
The GE Low HP sequence board DS3800HSQD1G1C is designed with a hole in each corner for inserting screws to secure the board in the drive. The GE Low HP serial board DS1HSQD3800G1C is also equipped with 1 2-pin connector and 40 1-pin connectors with fixed rods for securing ribbon cables. The board is also equipped with 20-pin connectors and 50 1-pin connectors. The board is also equipped with 20 erasable programmable read-only memory (EPROM) modules and one amber LED and one red LED.

The indicator LED DS3800HSQD1G1C on the GE Low HP sequence board enables the operator or technician to monitor the operation of the drive. At the same time, operators or technicians can monitor other drives and devices. This is because by taking a look at the indicator LED, the technician or operator can see if an error has occurred or if the operation is proceeding normally.

When the amber indicator lights up, the drive is started and the initial startup diagnostic test has passed. If the drive is started and the amber indicator remains off, it may indicate a problem. This may indicate that the drive has no power. Check that all power is going into the drive and that the power is working as required. If power is available, the drive may fail the initial diagnostic tests performed at boot time. Once the drive is able to start, perform a full range of diagnostic tests to investigate the problem.

GE DS3800HSQD1G1C 序列板 能够监控驱动器的操作

GE DS3800HSQD1G1C 序列板 能够监控驱动器的操作

型号推荐
4119 康吉森    Triconex DCS    通信模块
4119A 康吉森    Triconex DCS    通信模块
2551 康吉森    Triconex DCS    二酯型终止子
4000163-510 康吉森    Triconex DCS    模拟输出模块
4328 康吉森    Triconex DCS    网络通信模块
4329 康吉森    Triconex DCS    网络通信模块
4400 康吉森    Triconex DCS    网络通信模块
4500 康吉森    Triconex DCS    公路接口模块
4507 康吉森    Triconex DCS    公路接口模块
4609 康吉森    Triconex DCS    通信模块
4211 康吉森    Triconex DCS    通信模块
9566-810 康吉森    Triconex DCS    容错电路板
9566-8XX 康吉森    Triconex DCS    容错电路板

GE DS3800HSQD1G1C 序列板 能够监控驱动器的操作

在线客服
联系方式

热线电话

18059884797

邮箱

xiongbagk@gmail.com

上班时间

周一到周五

微信
WhatsApp
线