3500/64M 3500系统动态压力监测器

3500/64M 3500系统动态压力监测器

产品详情:

振动监测和机械健康管理:Bently 3500/64M电源控制器是Bently Nevada的产品之一，用于振动监测和机械健康管理系统。它为系统中的传感器、监测装置和其他关键组件提供电源供应，确保振动监测系统的正常运行。
旋转设备监测:该电源控制器可以用于监测和保护旋转设备，如涡轮机、发电机、压缩机等。它提供可靠的电源，支持振动监测系统对设备的实时监测和故障诊断。
能源行业: Bently 3500/64M电源控制器在能源行业中得到广泛应用。它可以应用于发电厂、核电站、石油和天然气设施等领域，为振动监测和机械健康管理系统提供电力支持。
工业自动化:该电源控制器可以用于工业自动化系统，为自动化控制设备和监测系统提供电源，确保设备的稳定运行和安全控制。配置键锁
它用于在“RUN”和“PROGRAM”模式之间切换3500机架。RUN模式可防止配置修改，同时允许机架正常运行。机架可以在本地或远程配置，同时仍可在PROGRAM模式下正常运行。通过从机架上的任一位置拔下钥匙，开关可以保持在运行或编程位置。您可以通过将开关锁定在运行位置来防止不必要的机架重新配置。任何时候需要远程重新配置机架时，都可以将开关锁定在PROGRAM位置。I/O模块信号公共端
两个版本的TDI /O模块中现在都有一个2针连接器，用于将信号公共端连接到机架的单点仪器接地。执行此操作后，要将信号公共端与底盘(安全)接地隔离，请沿“HP”箭头方向滑动电源输入模块(PIM)侧的选择器开关。

3500/64M 3500系统动态压力监测器

Product Details:

Vibration Monitoring and Mechanical Health Management: The Bently 3500/64M power controller is one of Bently Nevada's products for vibration monitoring and mechanical health management systems. It provides power supply to sensors, monitoring devices and other critical components in the system to ensure the normal operation of the vibration monitoring system.
Rotating equipment monitoring: The power controller can be used to monitor and protect rotating equipment such as turbines, generators, compressors, etc. It provides reliable power supply and supports real-time monitoring and fault diagnosis of equipment by vibration monitoring system.
Energy Industry: The Bently 3500/64M power controller is widely used in the energy industry. It can be used in power plants, nuclear power plants, oil and gas facilities to provide electrical support for vibration monitoring and mechanical health management systems.
Industrial automation: The power controller can be used in industrial automation systems to provide power for automated control equipment and monitoring systems to ensure stable operation and safe control of equipment. Configuration key lock
It is used to switch 3500 racks between "RUN" and "PROGRAM" modes. RUN mode prevents configuration modifications while allowing the rack to run properly. The rack can be configured locally or remotely while still operating in PROGRAM mode. The switch can be kept in the running or programmed position by unplugging the key from any location on the rack. You can prevent unnecessary rack reconfiguration by locking the switch in the run position. Any time you need to remotely reconfigure the rack, you can lock the switch in the PROGRAM position. I/O module signal public end
There is now a 2-pin connector in both versions of the TDI /O module for connecting the signal common end to the single point instrument ground of the rack. After doing this, to isolate the common end of the signal from the chassis (safety) ground, slide the selector switch on the side of the power input module (PIM) in the direction of the HP arrow.

3500/64M 3500系统动态压力监测器