5069-AENTR 是一款紧凑型5000以太网I/P通信适配器

5069-AENTR 是一款紧凑型5000以太网I/P通信适配器

Allen-Bradley 5069-AENTR是一款紧凑型5000以太网I/P通信适配器。该适配器与Compact 5000 I/O模块一起使用，允许在以太网网络上实现分布式I/O体系结构。它充当控制器和I/O模块之间的网关，并促进这些组件之间的数据传输。

5069-AENTR具有双以太网通信接口，支持10 / 100mbps和1gbps的通信速率。它支持线性、星形和环形拓扑结构，用于设计高可用性、冗余的以太网网络。该适配器支持安装多达31个Compact 5000 I/O模块，并提供系统侧电源和现场侧电源。

这个以太网I/P适配器使用Studio 5000 Logix设计器的28.00版本和更高版本进行配置。它可以被配置为作为设备级环(DLR)主管，并在受保护和不受保护的模式下工作。对于工业通信，该通信适配器主要支持Allen-Bradley的通用工业协议(CIP)。

5069-AENTR配有安全数字(SD)卡。它兼容1784-SD1和1784-SD2艾伦-布拉德利SD卡。第三方SD卡也可以使用，但是，功能不保证由艾伦-布拉德利。此通信适配器zui多可安装32gb内存。

5069-AENTR的工作温度为0℃+60℃。设备额定220v mA @ 18-32V DC MOD功率;SA电源5 mA @ 0-32V DC;2 mA @ 0-240V AC, 47…63 Hz ATEX/IECEx, 125V AC Max和SA功率通过9.95 A @ 0-32V DC;9.975 A @ 0-240V AC, 47…63 Hz ATEX/IECEx，zui大125V AC。

5069-AENTR是唯 一使用DHCP模式和Power RTB的适配器。它具有增强的状态指示器来跟踪和排除系统故障。它具有优越的隔离和内置电源输入，因为它有单独的系统电源。5069-AENTR在18-32V直流电流下有220毫安的MOD功率，在70毫秒MOD浪涌时有1750毫安的电源。在47- 63hz时，0-32V DC时具有5ma SA功率，0-240V AC时具有2ma SA功率。在18-32V DC时具有9.78 A MOD功率通。直流电压0 ~ 32v时的功率通率为9.95 A，交流电压0 ~ 240v时的功率通率为9.975 A，频率范围为47 ~ 63hz。5069-AENTR在MOD或SA电源RTB处不能超过10a，以免损坏。其隔离电压为300v，在1500V交流下连续测试60秒。建议SA电源在250V AC下的外部过流保护为20a。在22.5-43.2 A2t时具有10- 12a的快速作用电流，MOD电源推荐外部过流保护。5069-AENTR的电线尺寸为22-14 AWG的实心/绞合铜线，额定温度为221°F或更高，绝缘m为1.2 mm (3/64 in.)，仅单线连接。它的接地线是实心/绞合铜线14 AWG，额定221°F或更高，zui大直径3.5mm(0.14英寸)，包括单线连接的绝缘。对于以太网电缆连接，只能使用IEC 61918和IEC 61784-5-2。5069-AENTR工作温度为0 ~ 60℃，非工作温度为-40 ~ 85℃。其相对湿度为5-95%，不凝结。

5069-AENTR 是一款紧凑型5000以太网I/P通信适配器

The Allen-Bradley 5069-AENTR is a Compact 5000 Ethernet I/P communication adapter.  This adapter is used with the Compact 5000 I/O modules, allowing implementation of Distributed I/O architecture over an Ethernet network.  It acts as a gateway between the controllers and I/O modules and facilitates data transfer between these components.

The 5069-AENTR features dual Ethernet communication interface which support 10 / 100 Mbps and 1 Gbps communication rate.  It supports linear, star and ring topologies for design of high-availability, redundant Ethernet network.  This adapter supports installation of up to 31 Compact 5000 I/O modules and provides system-side power and field-side power as well.

This Ethernet I/P adapter is configured using Version 28.00 of Studio 5000 Logix designer and higher.  It may be configured to act as Device Level Ring (DLR) supervisor and function in protected and unprotected mode.  For industrial communication, Allen-Bradley’s Common Industrial Protocol (CIP) is primarily supported by this communication adapter.

The 5069-AENTR is provided with a Secure Digital (SD) card.  It is compatible with 1784-SD1 and 1784-SD2 Allen-Bradley SD cards.  Third party SD cards may be used as well however, functionality is not guaranteed by the Allen-Bradley.  Up to 32 GB of memory may be installed with this communication adapter.

The 5069-AENTR has an operating temperature of 0 °C +60 °C.  The device’ 220 mA @ 18-32V DC MOD power is rated;  SA Power of 5 mA @ 0-32V DC;  2 mA @ 0-240V AC, 47…63 Hz ATEX/IECEx, 125V AC Max and SA power passthrough of 9.95 A @ 0-32V DC;  9.975 A @ 0-240V AC, 47…63 Hz ATEX/IECEx, 125V AC Max.

The 5069-AENTR is the only adapter that uses a DHCP mode and Power RTB.  It has enhanced status indicators to track and troubleshoot systems.  It has superior isolation and built-in power input since it has separate system power.  The 5069-AENTR has 220 mA MOD power at 18-32V DC and 1750 mA for 70 ms MOD power inrush.  At 47-63 Hz, it has 5 mA SA power at 0-32V DC and 2 mA SA power at 0-240V AC. It has MOD power passthrough of 9.78 A at 18-32V DC.  Its SA power passthrough is 9.95 A at 0-32 V DC and 9.975 A at 0-240V AC with 47-63 Hz frequency.  The 5069-AENTR should not exceed 10 A at the MOD or SA power RTB to avoid damages.  Its isolation voltage is 300 V continuous tested at 1500V AC for 60 seconds.  Its recommended external overcurrent protection is 20 A at 250V AC for SA power.  It has a fast-acting current of 10-12 A at 22.5-43.2 A2t MOD power recommended external overcurrent protection.  The 5069-AENTR’s wire size is a solid/stranded copper wire of 22-14 AWG, rated at 221 °F, or greater, 1.2 mm (3/64 in.) insulation m, single-wire connection only.  Its grounding wire is a solid/stranded copper wire 14 AWG rated at 221 °F or greater, with a 3.5mm (0.14in) max diameter including the insulation for a single-wire connection only.  For the Ethernet cable connections, only the IEC 61918 and IEC 61784-5-2 should be used.  The 5069-AENTR has a 0 - 60 °C operating temperature and a -40-85 °C non-operating temperature.  Its relative humidity is 5-95% non-condensing.

5069-AENTR 是一款紧凑型5000以太网I/P通信适配器